Requirements of inverter for physical environment

Due to the high integration, compact overall structure and large heat dissipation, the hybrid inverter requires high temperature, humidity and dust content in the installation environment. When installing the solar inverter, it must provide a good operating environment for the inverter. The working ambient temperature of the inverter is rated at 40 ℃. If the ambient temperature is higher than 40 ℃ ~ 50 ℃, the rated current must be reduced. Otherwise, the temperature rise of the device will be too high, which will increase the possibility of device damage (especially IGBT power module), and have a great impact on normal and safe operation. If the working environment of the inverter fails to meet the requirements of the inverter on the working environment, it will cause high failure rate of the inverter, affect the long-term, reliable and safe operation, resulting in unnecessary economic losses. Therefore, the following matters should be paid attention to in the application of the inverter.

1.Operating temperature.
The inside of the inverter is a high-power electronic component, which is easily affected by the working temperature. The product is generally required to be 0-55 ℃, but in order to ensure the safety and reliability of the work, it should be considered to leave room for use, preferably controlled below 40 ℃. If the inverter is installed in the inverter cabinet, it shall be installed on the upper part of the cabinet and strictly comply with the installation requirements in the product manual. It is absolutely not allowed to install the heating element or the element easy to heat against the bottom of the inverter.

2.Ambient temperature.
When the temperature is too high and the temperature changes greatly, condensation is easy to occur inside the inverter, and its insulation performance will be greatly reduced, or even lead to short circuit accidents. If necessary, desiccant and heater must be added to the inverter cabinet. The surrounding humidity of the inverter shall be below 90%. If the surrounding humidity is too high, the electrical insulation will be reduced and the metal part will be corroded. If restricted by the installation site, the inverter shall not be installed in a place with high humidity, and the cabinet of the inverter shall be sealed as far as possible. In order to prevent condensation when the inverter stops, a convection heater should be added.

3.Corrosive gas.
If the concentration of corrosive gas is large, it will not only corrode the leads and printed circuit boards of components, but also accelerate the aging of plastic components and reduce the insulation performance. In this case, the inverter cabinet should be made into a closed structure and air exchange. There shall be no corrosive, explosive or combustible gas, dust and oil mist around the inverter. If there are explosive and combustible gases in the surrounding environment where the inverter is installed, there are relays and contactors that are easy to generate sparks in the inverter, so fire or explosion accidents may be caused sometimes. If there is dust and oil mist around the inverter, its adhesion and accumulation in the inverter will lead to the decrease of insulation; for the inverter with forced air cooling, the temperature in the inverter will rise abnormally due to the filter blockage, so that the inverter cannot operate stably.

4.Vibration and shock.
When the inverter cabinet is subject to mechanical vibration and impact, it will cause poor electrical contact. At this time, in addition to improving the mechanical strength of the inverter cabinet, away from the vibration source and impact source, the anti-seismic rubber pad shall be used to fix the inverter cabinet and electromagnetic switch and other components that generate vibration. The vibration resistance of the inverter should be different in different types. When the vibration exceeds the allowable value of the inverter, the fastening part of the components will be loose and the relay and contactor will act wrongly, which often leads to the unstable operation of the inverter. For the vibration situation that can be foreseen in advance, the vibration of inverter should be fully considered.

5.The altitude of inverter application is usually below 1000m.
If the altitude is high, the air pressure will be high, which is easy to cause insulation damage. In addition, the cooling effect of high elevation also decreases, so it is necessary to pay attention to the temperature rise of inverter.

REVO-II On/Off Gird Energy Storage Hybrid Inverter with Touch Screen

1.Touch screen display
2.PV and utility power take the load at same time(can setting)
3.Output power factor PF=1.0
4.On&Off Grid with energy storage
5.Energy generated record,load record,history information and fault record
6.Language and time setting
7.Structure with dust filter
8.AC charging and AC output time setting
9.Charging voltage and charging current timing
10.External Wi-Fi device optional
11.Parallel operation with up to 6 units only available for 3kW/4kW/5kW
12.Connected with battery optional
13.Wide PV input range 120-450VDC
14.Independent CPU
15.MAX PV Array power 4500W
16.Solar and Utility supply power to the load when solar power is not sufficient to load

评论

发表评论

此博客中的热门博文

Correct selection of backup time for UPS

图片
UPS backup time is generally a problem concerned by customer in the purchase process. Usually most people prefer to choose the  UPS  which power backup the longer the better, in fact, this is not correct. We must firstly clear that the seller will usually have standard type UPS and long-acting UPS. Standard type UPS with built-in battery, after a power interruption can supply power to the load equipment in general for a few minutes to tens of minutes, of course, the length of time depends on the load. Long acting UPS can not only meet the power requirement of load, but also meet the requirements of customers and work types and so on, so the long-term UPS is usually equipped with an external battery pack. If the client is not particularly strict to the work condition of the load, and the power of the load is not particularly large, usually with standard type UPS would be enough. Because the choice of long backup time UPS is bound to increase the number of battery groups an...
阅读全文

126th Canton Fair

图片
On Oct 15th 2019, as one of the most important trade promotion platforms for Chinese enterprises to expand the global market, Canton Fair in Guangzhou focused on highlighting innovation driven, and “independent brand” became a high-frequency word of Canton Fair. Xu Bing, a spokesman for the Canton Fair and deputy director of the China Foreign Trade Center, said that the domestic and foreign environment faced by China’s foreign trade development this year is more complex and uncertain. The majority of exhibitors accelerated quality improvement and innovation, and continued to make efforts in technology research and development, product innovation, brand cultivation, etc., with high technology, high quality, high added value and independent brand products emerging. Many independent innovative R & D products are welcomed by the market. At the same time, purchasers are less sensitive to price and pay more attention to the technology, brand, quality and service of products. In ...
阅读全文

How to maximize the efficiency of your UPS

图片
1.Use of AC voltage regulator After using  UPS power supply , there is no need to add AC voltage regulator. If it must be added, it should be added to the front level of UPS, that is, the mains power first passes through the AC voltage regulator, then through the ups, and then to the load. 2.Battery balanced charging skills At present, valve regulated lead-acid battery (VRLA) used in many ups power supply is called maintenance free battery from the beginning, which gives users a misunderstanding that it seems that this battery is durable and does not need maintenance at all. Under this kind of misleading, many users have not carried out maintenance and management since they installed the battery. When the battery in UPS power supply meets the following conditions, the battery shall be charged evenly: when the terminal voltage is lower than the specified calibration voltage due to excessive discharge. For 12 V small sealed lead-acid batteries, the discharge calibration voltage is...
阅读全文